AES Mechanical Seals

Convertor II™ - Cartridge Seal Designed To Replace Packing This cartridge seal is designed to replace two part component seals and conventional packing arrangements. The seal is offered with the following features: Cartridge design Hydraulically balanced seal face design Easy to install Modern, user-friendly design Excellent general service seal Non shaft fretting Reduced power consumption compared to packing Two bolt gland fixing	SCUSI™Single Cartridge Mechanical Seal with Flush Cartridge seal design Easy reliable installation Fits 5/16" (8mm) cross-section in smaller pumps Requires no pump modification Self-aligning faces Balanced seal faces Non-clogging internal rotary Reduces power consumption Eliminates leakage
CURC™ mechanical seals are part of a range of seals specifically designed to optimise the use of Silicon Carbide. CURC™ incorporates third generation self aligning technology. The design objective was to minimise metal to Silicon Carbide impact, particularly on start-up Self-aligning faces Cartridge design Easy to install Flush, quench and drain ports No shaft fretting Balanced seal faces Non-clogging internal rotary	CURC™ ANSI PLUS cartridge seal is available in a wide range of seal face, elastomer and alloy combinations to suit individual applications. A full range of seal support systems are available on request. Gland design to suit ANSI PLUS PUMPS Single cartridge seal with flush, quench & drain ports No shaft fretting Balanced seal faces Self-aligning faces Non-clogging internal rotary Eliminates leakage
CDSA™ cartridge double mechanical seal forms the basis of the engineered sealing system. The standard seal unit is 316 Stainless Steel with Carbon and Silicon Carbide faces and Viton® 'O' rings. This fundamental design is changed through modular component options to suit the requirements of the specific application. Self aligning faces inboard and outboard Cartridge design Available in exotic alloys (Wetted Parts) Pre-set unit for reliable installation Unique 'BI-METAL' design Double or tandem seal protection	CDSA™ ANSI PLUS cartridge seal is available in a wide range of seal face, elastomer and alloy combinations to suit individual applications. A full range of seal support systems are available on request. Gland design to suit ANSI PLUS PUMPS Single and double seal configuration Quench & drain ports Self-aligning stationaries Cartridge Design No shaft fretting Balanced seal faces Non clogging rotaries
Bi-Metal CDSA is a double cartridge mechanical seal design, with Exotic Alloy wetted components. The seal is inventoried with Hastelloy C, Hastelloy B, Titanium, Monel, and Alloy 20 wetted components as standard. The product is available from 1.000"-6.000" (24mm-150mm), in a wide range of seal face and elastomer combinations, in both standard and ANSI plus gland configurations. Double Cartridge Mechanical seal Modular Design Exotic Alloy wetted materials Patented design	CURE™ mechanical seal has been designed to bridge the gap between a single and a double cartridge seal. Traditionally this market sector is serviced by single seals using a rotary lip (e.g. an oil seal). Such designs are capable of sealing secondary fluids, at barrier pressures up to 10 psi g (2/3 of a bar g), but often experience limited lip seal life. This disadvantage is overcome with the CURE™ mechanical seal. Cartridge unit with secondary seal External seal with 10 psi g (2/3 of a bar g) capacity Short external working length Balanced seal faces (inboard and outboard) Non-clogging internal rotary Easy to install
CDM™ - Cartridge Double for Mixers The seal is offered with the following features: Accepts greater radial movement than AESSEAL® products designed for pumps Designed to run in vapour applications Quench and Drain environmental port options Exotic alloy wetted parts available Hydraulically balanced seal face design	DMSF™ - Double Monolithic Stationary Flow (Patent Pending) A double cartridge stationary seal with an integral pumping ring and monolithic seal faces. The seal is offered with the following features: Incorporates a bi-directional pumping scroll (patent pending) Directional barrier fluid cooling with the use of a deflector Stationary design Monolithic seal faces Designed to withstand barrier and process pressure fluctuations Double pressure and Hydraulically balanced seal faces 3/8" NPT large environmental control ports for cooling Patent pending seal face drive mechanism Cartridge seal

The above seals are only a fraction of the complete AES product line.
If you don't see the right seal here for you application, please contact us!

Logos on this page are copyrights of their respective companies.
The sunair logo is a registered trademark of the Sunair Co.